-
26CM BRUSH BUMPER
- Fits all standard size (26cm) Super-Lite, Ultimate & Xtreme (non-Sill) Brushes
- Fitted and removed in seconds
- Weight 35g
-
35CM BRUSH BUMPER
- White Rubber Brush Bumper – fits 35cm Ultimate & Xtreme Brushes
- Protects the stock edges – specially useful on historic or delicate windows
- Prevents stock edge wear for use on masonry window reveals
- Fitted and removed in seconds
- Weight 46g
- Please note: Does not include the brush it is shown fitted to
-
45CM BRUSH BUMPER
- Fits all 45cm Wide Super-Lite,Ultimate & Supreme Brushes
- Fitted and removed in seconds
- Weight 50g
-
BRUSH SIDE BUMPERS (PAIR) FOR XTREME SILL BRUSHES
- These clip over each side of the Xtreme Sill brush edges
- Provides window frame protection from hard stock edges
- Can be glued in position for maximum strength and durability
- Does not include brush pictured
-
DOODLEBUG REPLACEMENT WHITE ABRASIVE PAD
Replacement pad to fit the Doodlebug Swivel Pad Holder
-
GARDINER OVERSPRAY™
- Gardiner Over-Spray™ for use with all Gardiner poles with QuicK-LoQ™ Goosenecks
- Allows for quick and simple conversion of any pole to an internal spray system or any brush to an overhead rinsing brush
-
LONG SUPER-SCRAPER™
- Long Super Scraper – allows better reach in for use with deep-set windows and frames
- For use with all Gardiner poles with Quick-Release goosenecks
- Allows for quick and simple cleaning of heavily soiled glass
- Each Long Super-Scraper comes complete with 1x White Abrasive Pad
- Not compatible for use with a Gardiner gooseneck valve system
-
LOW PRESSURE – MICRO JET RINSE BAR – 35CM
- Supplied in Red
- 16 micro jets provide precise but gentle rinsing with brush on the glass
- Fits between brush and brush socket on any 35cm Gardiner brush
- Provides over-bristle micro jet rinsing
- Flow rate is half that of the standard 35cm micro-jet rinse-bar and about equivalent to standard pencil or Fanjets – recommended 1.5 – 2lpm
- Height of jets can be adjusted
- Can be used with internal brush jets as well
- Lightweight at 48g
- Uses John Guest connections on unit
- Uses standard Brush T Connector and jet hose – optional extra
- Needs 2 longer screws to allow it to be attached between brush body and brush socket (if used on standard brushes, will need 19mm screws. if used on Xtreme will need 16mm)
- Please note: The rinse bar does not come with the brush & gooseneck pictured
-
LOW PRESSURE – MICRO JET RINSE BAR – STANDARD WIDTH 26CM
- 16 micro jets provide precise but gentle rinsing with brush on the glass
- Fits between brush and brush socket on any standard width (26cm) Gardiner brush (not the Sill brush or Supreme)
- Provides over-bristle micro jet rinsing
- Flow rate is half that of the standard micro-jet rinse-bar and about equivalent to standard pencil or Fanjets – recommended 1.5 – 2lpm
- Jet angle is 3° higher than standard rinsebar to allow for lower flow rates
- Height of jets can be adjusted
- Can be used with internal brush jets as well
- Lightweight at 41g
- Uses John Guest connections on unit
- Uses standard Brush T Connector and jet hose – optional extra
- Needs 2 longer screws to allow it to be attached between brush body and brush socket (if used on standard brushes, will need 19mm screws. if used on Xtreme will need 16mm)
- Please note: The rinse bar does not come with the brush & gooseneck pictured
- Home
- About Us
- Our Services
- Contact Us
- News
- Shop
- Indoor and Specialized
- Pump and Hose
- Pure Water Systems
- Safety and Workwear
- Water-Fed Poles and Brushes